추천 제품
설명
Sheet resistance: <100 Ω/sq (flexo printed on SBS board with 18 BCM anilox roll)
Specific gravity: 1.09g/cm3
형태
liquid
점도
1300-1700 cP (Brookfield - low shear)
저장 온도
2-8°C
일반 설명
SunTronic GFT4600 flexo graphite ink is water-based graphite conductive ink designed for the production of conductive layers onto a variety of substrates via flexographic printing.
GFT4600 is appropriate for paper and cardboard substrates and also water-receptive polymer films and provides a unique combination of high-speed printability, fast drying, and conductivity in an easy-to-use ink system. GFT4600 can also be printed on plastic films bearing a water-receptive primer
GFT4600 is appropriate for paper and cardboard substrates and also water-receptive polymer films and provides a unique combination of high-speed printability, fast drying, and conductivity in an easy-to-use ink system. GFT4600 can also be printed on plastic films bearing a water-receptive primer
주의사항
DRYING
GFT4600 is a fast drying ink that will dry to the touch between 150-300 feet per minute using standard dryers found on flexographic presses. Maximum conductivity can be achieved with further drying, inline or offline, using infrared (IR) dryers, high capacity forced hot air ovens and/or heated mandrels. Optimum drying conditions should be established for particular equipment used by the customer.
GFT4600 is a fast drying ink that will dry to the touch between 150-300 feet per minute using standard dryers found on flexographic presses. Maximum conductivity can be achieved with further drying, inline or offline, using infrared (IR) dryers, high capacity forced hot air ovens and/or heated mandrels. Optimum drying conditions should be established for particular equipment used by the customer.
PRINTING
GFT4600 is supplied as ready-for-use ink. Soft sediment may occur over time so thorough mixing prior to use is necessary. The ink may be diluted with water up to 3%, however sheet resistivity will increase slightly. Dilute with caution!
The below details are only a guide, and the final choice of flexo printing specifications may depend on substrate and web speed. To achieve maximum coverage, high volume anilox rolls are recommended (80-120 lpi with 14-22 BCM).
Continuous anilox rotation is required throughout the print run to avoid ink drying on flexo plate and anilox roll. GFT4600 should not be allowed to dry completely on printing equipment. Prompt cleaning with water is highly recommended. Anilox rolls should be also cleaned using a sonicating bath after each print run.
GFT4600 is supplied as ready-for-use ink. Soft sediment may occur over time so thorough mixing prior to use is necessary. The ink may be diluted with water up to 3%, however sheet resistivity will increase slightly. Dilute with caution!
The below details are only a guide, and the final choice of flexo printing specifications may depend on substrate and web speed. To achieve maximum coverage, high volume anilox rolls are recommended (80-120 lpi with 14-22 BCM).
Continuous anilox rotation is required throughout the print run to avoid ink drying on flexo plate and anilox roll. GFT4600 should not be allowed to dry completely on printing equipment. Prompt cleaning with water is highly recommended. Anilox rolls should be also cleaned using a sonicating bath after each print run.
법적 정보
SunTronic is a registered trademark of Sun Chemical, Inc.
Storage Class Code
10 - Combustible liquids
WGK
nwg
Flash Point (°F)
Not applicable
Flash Point (°C)
Not applicable
시험 성적서(COA)
제품의 로트/배치 번호를 입력하여 시험 성적서(COA)을 검색하십시오. 로트 및 배치 번호는 제품 라벨에 있는 ‘로트’ 또는 ‘배치’라는 용어 뒤에서 찾을 수 있습니다.
이미 열람한 고객
문서
Professors Tokito and Takeda share design principles and optimization protocols for organic electronic devices, focusing on flexibility and low cost.
자사의 과학자팀은 생명 과학, 재료 과학, 화학 합성, 크로마토그래피, 분석 및 기타 많은 영역을 포함한 모든 과학 분야에 경험이 있습니다..
고객지원팀으로 연락바랍니다.