Skip to Content
MilliporeSigma
  • Trace-level determination of sweeteners in sewage sludge using selective pressurized liquid extraction and liquid chromatography-tandem mass spectrometry.

Trace-level determination of sweeteners in sewage sludge using selective pressurized liquid extraction and liquid chromatography-tandem mass spectrometry.

Journal of chromatography. A (2015-07-23)
Paula Arbeláez, Francesc Borrull, Rosa Maria Marcé, Eva Pocurull
ABSTRACT

The occurrence of sweeteners in the environment has become a matter of concern due to the possibility of adverse effects on human health and wildlife species. One of the routes by which sweeteners enter the environment is through sewage sludge. Therefore, a method was developed with a selective-pressurized liquid extraction (S-PLE) followed by liquid chromatography-tandem mass spectrometry for the simultaneous determination of eight sweeteners in sewage sludge. The chromatographic separation was achieved in less than ten minutes using an amide polar-embedded reversed-phase column. Due to the high matrix effect present in the sample, an extensive study was conducted in order to overcome this issue, with C18 in-cell and solid-phase extraction (Oasis HLB) as a clean-up method. S-PLE/SPE recoveries at two levels of concentration (50μg/kg and 1000μg/kg in dry weight (d.w.), n=5) were higher than 61%. Repeatability and reproducibility at the same concentrations (%RSD, n=5) were lower than 11% and 16%, respectively. The limits of detection were 10μg/kg (d.w) for all compounds, except for cyclamate (5μg/kg (d.w.)). The method was successfully applied to sewage sludge samples from three sewage treatment plants located in Catalonia (Spain). Of the eight compounds, five were determined in all of the samples analysed, with acesulfame and saccharine being recorded at the highest concentrations of up to 481μg/kg and 591μg/kg (d.w.), respectively.

MATERIALS
Product Number
Brand
Product Description

Sigma-Aldrich
Acetonitrile solution, contains 10.0% acetone, 0.05% formic acid, 40.0% 2-propanol
Sigma-Aldrich
Acetonitrile solution, contains 0.05 % (w/v) ammonium formate, 5 % (v/v) water, 0.1 % (v/v) formic acid, suitable for HPLC
Sigma-Aldrich
Sucralose, ≥98.0% (HPLC)
Sigma-Aldrich
Acetonitrile solution, contains 0.05 % (v/v) trifluoroacetic acid
Sigma-Aldrich
Acetonitrile solution, contains 0.1 % (v/v) trifluoroacetic acid, suitable for HPLC
Sigma-Aldrich
Aluminum oxide, mesoporous, MSU-X (wormhole), average pore size 3.8 nm
Sigma-Aldrich
Acetonitrile solution, contains 0.1 % (v/v) formic acid, suitable for HPLC
Sigma-Aldrich
Acetonitrile, for chromatography
Sigma-Aldrich
L-Lysine monohydrochloride, SAJ special grade, ≥99.0%
Sigma-Aldrich
Acetonitrile, ≥99.8%, for residue analysis, JIS 1000
Sigma-Aldrich
Formic acid, JIS special grade, ≥98.0%
Sigma-Aldrich
Acetonitrile, ≥99.8%, for residue analysis, JIS 300
Sigma-Aldrich
Acetonitrile, JIS special grade, ≥99.5%
Sigma-Aldrich
Acetonitrile, ≥99.8%, suitable for HPLC
Sigma-Aldrich
Acetonitrile, SAJ first grade, ≥99.0%
Sigma-Aldrich
Aluminum oxide, nanoparticles, <50 nm particle size (DLS), 20 wt. % in isopropanol
Sigma-Aldrich
Aluminum oxide, nanopowder, 13 nm primary particle size (TEM), 99.8% trace metals basis
Sigma-Aldrich
Acetonitrile, HPLC Plus, ≥99.9%, poly-coated bottles
Sigma-Aldrich
Aluminum oxide, nanoparticles, 30-60 nm particle size (TEM), 20 wt. % in H2O
Sigma-Aldrich
Aluminum oxide, CP
Sigma-Aldrich
Acetonitrile, for residue analysis, JIS 5000
Sigma-Aldrich
Aluminum oxide, single crystal substrate, <0001>
Sigma-Aldrich
Acetonitrile, electronic grade, 99.999% trace metals basis
Sigma-Aldrich
Aluminum oxide, nanowires, diam. × L 2-6 nm × 200-400 nm
Supelco
Acetonitrile, HPLC grade, ≥99.93%
Sigma-Aldrich
Aluminum oxide, 99.997% trace metals basis
Sigma-Aldrich
Formic acid, ≥95%, FCC, FG
Sigma-Aldrich
Aluminum oxide, nanopowder, <50 nm particle size (TEM)
Sigma-Aldrich
Acetonitrile, anhydrous, 99.8%
Sigma-Aldrich
Acetonitrile, ≥99.5%, ACS reagent